Boiler pressure too high: how to bring it down safely
Most boilers should read between 1 and 1.5 bar when the heating is off, and up to about 2 bar when it’s running. If the gauge goes above 2.5 bar, the pressure is too high. You can usually bring it down yourself by letting a little water out of a radiator. If it keeps climbing back up, something in the system needs fixing.
What’s normal boiler pressure?
This applies to combi and system boilers, which have a pressure gauge on the front or underneath. Older boilers with a water tank in the loft don’t usually have one.
Heating off, system cold: about 1 to 1.5 bar.
Heating on, system hot: a little higher, often up to about 2 bar. Water expands as it heats, so a small rise is normal.
Above 2.5 bar: too high. At about 3 bar, a safety valve opens and lets water out through a small pipe outside.
Why does boiler pressure go too high?
Too much water was added when topping up. This is the most common cause, often after a top-up with the heating on.
The filling loop was left open, or is letting water through. The filling loop is the hose or tap used to top up. If one of its taps doesn’t close fully, mains water keeps creeping in.
The expansion vessel has lost its charge. This tank inside or near the boiler takes up the extra water as it heats. When it stops working, the pressure jumps every time the heating comes on.
A faulty gauge. Less often, the gauge itself is wrong.
How to bring boiler pressure down safely
Turn the heating off and let the system cool for an hour or so. Check the gauge again, as it may drop on its own.
Check both taps on the filling loop are fully closed.
If it’s still above 1.5 bar, go to a radiator, ideally downstairs, and hold a cloth and a small container under the bleed valve.
Open the valve slowly with a radiator key. Air may come out first, then water.
Watch the boiler gauge, or have someone call it out to you. Close the valve when it reads about 1.2 to 1.5 bar.
Turn the heating back on and check the pressure over the next day or two.
Not usually in the short term. Boilers have a pressure relief valve that opens before the pressure gets unsafe, which is why you might see water dripping from a small copper pipe on an outside wall. But that valve isn’t meant to open regularly. If it does, it can start to leak, and the boiler may lock out. Don’t leave high pressure for weeks. Never open the boiler casing or try to adjust parts inside it. That’s a job for a Gas Safe registered engineer.
When to call an engineer
Give us a call if:
The pressure climbs back up after you’ve brought it down
It jumps by more than about half a bar every time the heating comes on
Water keeps dripping from the pipe outside
The boiler shows a fault code or won’t fire up
These usually point to the filling loop, the expansion vessel or the relief valve, which our engineers can test and fix through our boiler repair service. If your pressure keeps dropping instead, see why your boiler keeps losing pressure.
MS HEATING AND PLUMBING has been repairing boilers across Birmingham and Solihull for nearly 30 years. Our engineers are Gas Safe Registered, and we’re a Which? Trusted Trader.
Frequently asked questions
What should my boiler pressure be?
About 1 to 1.5 bar with the heating off. It can rise to about 2 bar when the heating is on. Your boiler manual gives the exact figure for your model.
Is 3 bar boiler pressure too high?
Yes. At about 3 bar the pressure relief valve opens and lets water out. Bring it down by bleeding a radiator, and call an engineer if it keeps happening.
Why does my boiler pressure go up when the heating is on?
Water expands as it heats, so a small rise is normal. A big jump, of more than about half a bar, usually means the expansion vessel needs recharging.
Why is water dripping from the pipe outside my house?
If it comes from a small copper pipe near the boiler, it’s usually the pressure relief valve letting water out because the pressure is too high. Get it checked if it keeps dripping.
Can I reduce boiler pressure without bleeding a radiator?
Letting the system cool can bring it down a little. Otherwise bleeding a radiator is the safe way. Never open the boiler or its relief valve yourself.
How to bleed a radiator, and when it won’t fix the problem
Bleeding a radiator lets out trapped air so it heats up properly. Here’s how to do it safely, which one to start with, and what to do if it doesn’t help.