How to bleed a radiator, and when it won’t fix the problem
Bleeding a radiator lets out air trapped at the top, so hot water can fill it again. It takes a few minutes, needs a radiator key and a cloth, and is one of the few heating jobs that’s safe to do yourself. If a radiator is still cold afterwards, or needs bleeding again within weeks, the problem is something else, and we explain what below.
When does a radiator need bleeding?
A radiator needs bleeding when it’s cold at the top and warm at the bottom. Air rises, so it collects at the top and stops hot water reaching it. You may also hear gurgling or ticking from the radiator or pipes when the heating comes on. If it’s cold at the bottom instead, bleeding won’t help: see our guide to a radiator cold at the bottom or the top.
What you need
A radiator key, from any DIY shop. Some newer valves take a flat screwdriver instead.
An old cloth or towel to catch the water.
A small container, in case more water comes out than you expect.
How to bleed a radiator, step by step
Turn the heating off and wait until the radiators are cool. Hot water can spray out of a warm radiator.
Find the bleed valve. It’s a small square or slotted fitting at one of the top corners.
Hold the cloth under the valve and fit the key.
Turn the key slowly anticlockwise, about a quarter of a turn. You’ll hear a hiss as the air escapes.
When water starts to come out in a steady trickle, turn the key clockwise to close the valve. Don’t over-tighten it.
Wipe up any drips and do the same on any other radiators with cold tops.
Check the pressure gauge on your boiler. If it has dropped below about 1 bar, top it up using the filling loop, following your boiler manual.
Turn the heating back on and check the radiators warm up evenly.
Which radiator should you bleed first?
If several radiators need bleeding, start downstairs with the one furthest from the boiler, then work your way back towards it. Do the upstairs radiators last. This pushes the air through the system in one direction rather than moving it from room to room.
What if no water comes out?
If you open the valve and nothing comes out at all, not even air, the valve may be blocked with paint or sludge. If you hear air but no water follows, the system pressure may be too low. On a combi or system boiler, check the gauge and top it up. On an older system with a tank in the loft, the tank may not be filling. Close the valve and give us a call if you’re not sure.
When bleeding won’t fix the problem
Dark or black water comes out: that’s sludge, and the radiator probably has a cold bottom too. A power flush clears it out.
The whole radiator stays cold: check both valves are open. A thermostatic valve can stick, especially after the summer.
You need to bleed it again within a few weeks: air is getting into the system. On a sealed system this often goes with pressure that keeps dropping, which usually means a leak. See why your boiler keeps losing pressure.
Some rooms are always cooler than others: the system may need balancing so hot water reaches every radiator evenly.
MS HEATING AND PLUMBING has been looking after heating systems across Birmingham and Solihull for over 29 years. Our engineers are Gas Safe Registered, and we’re a Which? Trusted Trader.
Frequently asked questions
How often should I bleed my radiators?
Only when they need it, usually once a year at most, before winter. If a radiator needs bleeding every few weeks, air is getting into the system and it’s worth getting checked.
Should the heating be on or off when I bleed a radiator?
Off, and the radiators cool. Hot water can spray out of the valve, and with the pump off the air settles at the top where it’s easiest to let out.
Can I bleed a radiator without a key?
Some newer bleed valves take a flat screwdriver. Older ones need a radiator key, which costs very little from any DIY shop. Pliers can round off the valve, so avoid them.
Why does water keep coming out of the bleed valve?
That means the air is out and the valve should be closed. Turn it clockwise until it stops. If it won’t close or keeps dripping, the valve may need replacing.
Do I need a heating engineer to bleed a radiator?
No, it’s a simple job most people can do. Call an engineer if bleeding doesn’t help, the water is black, or the pressure keeps dropping afterwards.
Still got cold radiators?
For a quote on a power flush or a sticking valve, send us photos on WhatsApp of the radiator and your boiler. If your heating has stopped working, give us a call on 0121 709 0000 and we’ll help.
Combi, system or regular boiler: which suits your home?
The right boiler depends on your home’s size, how many bathrooms you have and your water pressure. A plain-English guide to combi, system and regular boilers.